Where is the main fuse on a motorcycle?

Normally you would install the main fuse on the live side of the battery in-line with the wire which goes from the battery and up to the ammeter connections for distribution to the lights and other accessories.

Where is the main fuse located?

The main fuse box is located on the passenger’s side near the battery. To open it, push the two tabs as shown. All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in three fuse boxes.

How do I know which fuse is blown?

Look at the fuse wire. If there is a visible gap in the wire or a dark or metallic smear inside the glass then the fuse is blown and needs to be replaced. If you cannot see whether the fuse is blown, follow steps 4 and 5. If the fuse is definitely blown, go to step 6.

Why does my bike have no power?

Take the battery to an auto parts store and have them test it. If the battery fails their test, replace the battery. Next, check the main fuse, usually on the same cable as the positive battery connector. … Then check the fuses in fuse box, doing as with the main fuse if any are blown.

IT IS INTERESTING:  Is Indian motorcycle owned by Harley Davidson?

What amp fuse do I need?

Plugs for appliances rated between about 700 watts and 3000 watts (the maximum rating of a wall socket) should be fitted with a 13-amp fuse (coloured brown). For example: 13A Fuse – Washing machine, dishwasher, microwave, kettle, toaster, iron.

What are the 3 types of fuses?

Different Types of Fuses – Constriction, Working & Characteristics

  • DC Fuses.
  • AC Fuses.
  • Cartridge Fuses.
  • D – Type Cartridge Fuse.
  • HRC (High Rupturing Capacity) Fuse or Link Type Cartridge Fuse.
  • High Voltage Fuses.
  • Automotive, Blade Type & Bolted Type Fuses.
  • SMD Fuses (Surface Mount Fuse), Chip , Radial, and Lead Fuses.

What will cause a fuse to keep blowing?

The fuse is the incorrect amperage rating

Check what devices or lights are on that circuit, as it may be the case that a new amplifier pulls too much power, causing the fuse to blow. … The number embossed on the fuse, such as 5, 10 or 15, indicates how many amps may be pulled through the fuse before it blows.

How do I know if my multimeter fuse is blown?

Fuse is OK: If the multimeter reading changes to a low resistance value (similar to the result of touching the 2 leads together). Fuse is Blown: If the meter reading does not change and display still shows the original 100% resistance state. Don’t forget to turn the multimeter OFF when you have finished testing.

Can a fuse be blown and not look like it?

Due to the way fuses are engineered, the likelihood that a fuse would become faulty without blowing is pretty slim, but there are rare instances in which a fuse might appear completely fine, even though no current runs through it.

IT IS INTERESTING:  How do you know if your motorcycle is burning oil?

Can a blown fuse drain car battery?

When the circuit transmits too much electricity, the fuse heats up, then “pops”, not allowing anymore electricity to flow. The fuse in and of itself cannot be the cause of the power drain. … If by pulling the fuse you get a noticeable drop in battery drain, whatever is causing the drain is on that circuit.

Why is my bike losing power when I accelerate?

You may have excess slack on the throttle cable where it is connected to the carburetor. This in turn will lessen it’s ability to open the butterfly valve because it’s not giving it a full pull. You will have an uneven air and fuel mix which will cause your motorcycle to lose power when accelerating.

How do you know if your motorcycle is low on gas?

The normal way to tell you’re low on gas is if you have to switch to reserve. FI bikes generally have a low fuel light, though. With a bike with a reserve, you reset your tripometer at a full fill up, then wait until you hit reserve with normal riding.

How do you troubleshoot a motorcycle?

What to Do When Your Motorcycle Won’t Start (But the Battery is Good)

  1. Confirm There’s Gas in the Tank. …
  2. Engage the Clutch. …
  3. Put the Motorcycle in (the Right) Gear. …
  4. Look for Loose Wires. …
  5. Confirm the Kill Switch is Off. …
  6. Ensure the Fuel Valve is Set to “On” …
  7. See if the Fuel Injection System is Functional.
Types of transport